Gino Development 02-0444 TruePower Punch & Die Set (9 Piece)

Gino Development 02-0444 TruePower Punch & Die Set

Clear plate guide for easy alignment. Made from precision ground hardened alloy steel. Accurate to within 0.002". Includes nine punches: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8" & 3/4". Capacities: 20 Gauge Steel Sheet, 13 Gauge Aluminum & Brass. Includes blow molded storage case. INITIAL ADJUSTMENT If you find the punches have a tight fit, are difficult to insert through the clear plate guide and cannot be moved by firm hand pressure, turn over the punch & die set and lightly tap each punch through the appropriate die from the tool steel plate toward the clear top. Always insert punches with the cutting edge first. The hammerhead should always squarely strike the punches on top of the beveled end. NEVER strike the cutting edge end of the punch with a hammer. Repeat this procedure several times until the fit becomes workable. Insertion of the punches will become easier after continued use. TO PUNCH A HOLE 1. Position the material to be punched between the tool steel base and the clear plate guide. 2. Before striking the punch, make sure the punch has been pushed through the clear plate guide and the cutting edge of the punch is touching the material. 3 Strike the beveled end of the punch squarely with the hammer face. Use enough force to penetrate the material with one b...

  • Brand: Gino Development
  • ASIN: B0010ZM6EW
  • UPC: 870208004441

Precision Brand Punch and Die Set

Precision Brand Punch and Die

Punch and Diet set is packaged in a durable plastic case. The base and punches are made of a hardened and ground A-2 tool steel. Mark center lines, align with center lines and hit with hammer.

  • Brand: Precision Brand
  • ASIN: B000LDG906
  • UPC: 698158401055

Precision Brand TruPunch Punch and Die Set

Precision Brand TruPunch Punch and Die

Precision Brand TruPunch makes perfect, custom washers, shims, and gaskets in seconds by using its exclusive, patented punch, pilot, and pin system. No guess work is needed to center the I.D. and there is no need to scribe center lines. Material waste is reduced by creating a perfect shim every time. Packaged in a durable plastic case.

  • Brand: Precision Brand
  • ASIN: B00065UY8C
  • UPC: 698158401109

15ton Hydraulic Knockout Punch Kit Hand Pump 11 Dies Tool Hydraulic Opener

15ton Hydraulic Knockout Punch Kit Hand Pump 11

This Brand New Complete 15-Ton Hydraulic Punch Driver Kit, even tough material like 11-gauge steel will easily be pierced by this punch kit. It's great for installing and repairing wire pipeline, signal lamp and instrument in metallurgy, petrol, electronics, electrical appliance,chemical industry, ship & machinery and many more! The tool can make a hole on ≤4mm thick metal plate. It's easy operation, effort, fast speed, processing with smooth surface, no site limitation, safe and reliable, light structure, beautiful, easy to carry. Features: 11 Dies & Punches Interchangeable to Meet Different Needs Plastic Grip at the End of the Long Steel Handle Rotatable ON / OFF Switch for safe operation Easy Seating with the Brackets on the Bottom of the Hydraulic Pump Portable Metal Case for Convenient traveling Two Metal Clasps to Lock the Kit Firmly Laborsaving and Fast Operation Accommodating More Material: Stainless Steel, Aluminum, Steel, Plastic etc. Specification: Max Pressure:15 ton Max Thickness for Steel: 3.2 mm ( 11 gauge ) Max Thickness for Stainless Steel: 2 mm ( 14 gauge ) Ram with 50 1/2" High Pressure Hose 11pc Dies & Punches : 1/2", 3/4", 1", 1 1/4", 1 1/2", 2", 2 1/2", 3", 3 1/2", 4",4 1/2" 2pc Piston Shafts : 4 3/4"L x 3/4"Diam & 3 1/8"L x 3/4"Diam 2p...

  • Color: Yellow
  • Brand: Comie
  • ASIN: B00SF204TC

Coin Ring Center Punch for Quarters. Comes with 1/2" Punch and Die Set. 24.3mm SALE! SALE! SALE!

Coin Ring Center Punch for Quarters. Comes with

Hi! Up for sale is one, U.S. Quarter Center punch set. I MAKE COIN RINGS AS WELL. I have punched out over 200 plus coins with this same punch design and Same Punch, still truckin!! The punch body is 24.3mm I.D., for U.S. Quarters, and comes with 1/2" punch and die set. The punch is O1 Tool Steel, 2 inches long. Hardened, and hollow ground, and has a relief, to make it easier to get the coin back off. The die is also O1 Tool Steel, hardened, and relief ground, so your blank falls out. This is an aluminum body and guide. The guide is reamed within .0005" (half of 1 thousand") for 1/2" shanked punches. Overall height is 2-3/4" with a coin. The O.D. is 1-5/8". This is to be used in a press. Hammers ruin punches, and will VOID the warranty, no exceptions. Thanks for your business, and have a great day!

  • ASIN: B016U1Z386

9 Piece Punch and Die Set

9 Piece Punch and Die

Made of precision ground hardened alloy steel, this punch set can power through 20 gauge sheet steel and 13 gauge aluminum and brass with ease. Accurate to within 0.002, this punch and die set includes a clear plate for easy alignment, nine punches, a 9-hole die and a custom storage case for easy organization and portability. The punches are 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 5/8 and 3/4 in diameter.

  • Brand: Lifetime Carbide
  • ASIN: B006ZBCFDI
  • UPC: 792363955478

14 Piece Circle and Round Disc Cutter Set - 1/8" to 5/8" Jewelry Making Metal Cutting Forming Pendant Charm Coin Punch Tool

14 Piece Circle and Round Disc Cutter Set

Made from high-density steel, this item is great for cutting up to 18 gauge sized soft metals.Sizes: 1/8" - .118" - 3 mm, 11/64" - .177" - 4.5 mm, 3/16" - .196" - 5 mm, 15/64" - .236" - 6 mm, 17/64" - .275" - 7 mm, 9/32" - .295" - 7.5 mm, 5/16" - .314" - 8 mm, 11/32" - .344" - 8.5 mm, 25/64" - .393" - 10 mm, 7/16" - .433" - 11 mm, 15/32" - .472" - 12 mm, 1/2" - .511" - 13 mm, 9/16" - .551 - 14 mm, and 5/8" - .629" - 16 mm. Cuts soft metals up to 18 gauge.Instructions: Use a disk cutter on top of a rubber bench block or pad for support. Use a cutting lubricant, such as "Cut Lube" to lubricate the cutting edges of the punch. Use a suitable mallet, never a nail driving hammer. We suggest our 1 lb or 2 lb brass mallets which you can find for sale on our website. Always support the opposite side of the cutter with a sheet of the same diameter metal that you are cutting. (This will help keep the upper and lower parts of the disk cutter in alignment and help minimize material sticking in the disk cutter). Do not exceed the maximum thickness recommended for your disk cutter. Only cut soft non-ferrous metals like brass, copper, silver and gold. Make sure your cutting edges are down. To prevent rust, keep your disk cutter lubricated between use and store in a dry location. We recommend to ...

  • Color: Silver
  • Brand: PMC Supplies LLC
  • ASIN: B00E9F8V58

6MM 1/4" Steel Punch Stamp Die Set Metal 36 Pc Numbers & Letters in plastic case

6MM 1/4" Steel Punch Stamp Die Set Metal

Stamp letters & numbers into steel and other metals, wood, leather, vinyl or plastic Complete set of 26 upper-case letters, ampersand (&) and numbers 0 - 9; professional quality Larger characters are easy-to-read, 1/4" height (6mm); set weight 40 oz High-durability hardened and tempered carbon steel 2-1/2" length with 5/16" square shank Permanently identify equipment, tools & valuables; customize woodworking projects, imprint initials.

  • ASIN: B0122BPL2Q

5/8" Shanked Punches and Dies (3/8")

5/8" Shanked Punches and Dies

Hi There We are offering a punch and die set for Coin Ring Center Punches. The set contains 1 punch and 1 Die. You will be able to choose from the following sizes: 5/8" 1/2" 7/16" 3/8" 9/16" The punches are 5/8" shanked by 2" long. They are also hollow ground for easier cutting and have a relief angle. They are made from hardened tool steel. Thank you for looking!!!!

  • Brand: CoinRingMagic
  • ASIN: B01BXNUUB6
Similar Punch And Die Shopping
Punch And Die Video Reviews